SDS

A listing of SDS's
SAFETY DATA SHEET
Mechanical Pump Oil
1. IDENTIFICATION
Product Identifiers
Product Name:
Mechanical Pump Oil
Other Names:
DTE Oil Medium
Product Number(s):
M007
CAS Number:
?
Recommended use of the chemical and restriction on use
Laboratory use. Rotary vane vacuum pump oil; Turbine oil.
Company Details
ProSciTech Pty Ltd
11 Carlton Street
KIRWAN QLD 4817
Australia

(07) 4773 9444
www.proscitech.com
Emergency Contact Details
ProSciTech Pty Ltd
11 Carlton Street
KIRWAN QLD 4817
Australia

(07) 4773 9444
www.proscitech.com
2. HAZARDS IDENTIFICATION
Classification of the substance or mixture
Not classified as hazardous according to criteria of NOHSC.
Label Elements
Signal Words
None
Hazard Statement(s)
NON?HAZARDOUS SUBSTANCE. NON?DANGEROUS GOODS.
Precautionary Statement(s)
Not applicable.
Primary route(s) of entry
Not available.
Human Health
Inhalation:
Not available.
Ingestion:
Not available.
Eyes:
Not available.
Skin:
Not available.
Environment
No further relevant information available.
3. COMPOSITION/INFORMATION ON INGREDIENTS
No information available.
4. FIRST AID MEASURES
Ingestion
First aid is normally not required. Seek medical attention if discomfort occurs.
Inhalation
Remove from further exposure. For those providing assistance, avoid exposure to yourself or others. Use adequate respiratory protection. If respiratory irritation, dizziness, nausea, or unconsciousness occurs, seek immediate medical assistance. If breathing has stopped, assist ventilation with a mechanical device or use mouth?to?mouth resuscitation.
Skin Contact
Wash contact areas with soap and water. If product is injected into or under the skin, or into any part of the body, regardless of the appearance of the wound or its size, the individual should be evaluated immediately by a physician as a surgical emergency. Even though initial symptoms from high pressure injection may be minimal or absent, early surgical treatment within the first few hours may significantly reduce the ultimate extent of injury.
Eye Contact
Flush thoroughly with water. If irritation occurs, get medical assistance.
Other Information
No further relevant information available.
5. FIREFIGHTING MEASURES
Suitable extinguishing equipment
Use water fog, foam, dry chemical or carbon dioxide (CO₂) to extinguish flames. DO NOT USE straight streams of water.
HAZCHEM
Not available.
Special protective equipment and precautions for fire fighters
No special measures required.
6. ACCIDENTAL RELEASE MEASURES
Personal precautions, protective equipment and emergency procedures
Avoid contact with spilled material. See Section 5 for firo fighting information. See the Hazard Identification Section for Significant Hazards. See Section 4 for First Aid Advice. See Section 8 for advice on the minimum requirements for personal protective equipment. Additional protective measures may be necessary, depending on the specific circumstances and/or the export judgment of the emergency responders. For emergency responders: Respiratory protection: respiratory protection will be necessary only In special cases, e.g., formation of mists. Half-face or full-face respirator with filter(s) for dust/organic vapour or Self Contained Breathing Apparatus (SCBA) can be used depending on the size of spill and potential level of exposure. If the exposure cannot be completely characterised or an oxygen deficient atmosphere Is possible or anticipated, SCBA Is recommended. Work gloves that are resistant to hydrocarbons are recommended. Gloves made of polyvinyl acetate (PVA) arc not water-resistant and are not suitable for emergency use. Chemical goggles are recommended if splashes or contact with eyes is possible. Small spills: normal antistatic work clothes are usually adequate. Large spills: full body suit of chemical resistant, antistatic material is recommended.
Environmental precautions
Large Spills: Dyke far ahead of liquid spill for later recovery and disposal. Prevent entry into waterways, sewers, basements or confined areas.
Methods and materials for containment and clean up
Notify relevant authorities in accordance with all applicable regulations.Land Spill: Stop leak if you can do so without risk. Recover by pumping or with suitable absorbent.
Water Spill: Stop leak if you can do so without risk. Confine the spill immediately with booms. Warn other shipping. Remove from the surface by skimming or with suitable absorbents. Seek the advice of a specialist before using dispersants. Water spill and land spill recommendations are based on the most likely spill scenario for this material; however, geographic conditions, wind, temperature, (and in the case of a water spill) wave and current direction and speed may greatly influence the appropriate action to be taken. For this reason, local experts should be consulted. Note: Local regulations may prescribe or limit action to be taken.
7. HANDLING AND STORAGE
Precautions for safe handling
Prevent small spills and leakage to avoid slip hazard. This material is a static accumulator.
Material can accumulate static charges which may cause an electrical spark (ignition source). When the material is handled in bulk, an electrical spark could ignite any flammable vapours from liquids or residues that may be present (e.g., during switch-loading operations). Use proper bonding and/or ground procedures. However, bonding and grounds may not eliminate the hazard from static accumulation. Consult local applicable standards for guidance.
Conditions for safe storage
The container choice, for example storage vessel, may effect static accumulation and dissipation In open or unlabelled containers. Keep away from incompatible materials.
Do not store in open or unlabelled containers.
8. EXPOSURE CONTROLS/PERSONAL PROTECTION
Exposure Standards
Engineering controls
The level of protection and types of controls necessary will vary depending upon potential exposure conditions.Control measures to consider: No special requirements under ordinary conditions of use and with adequate ventilation.
Personal protective equipment
Eye and face protection
If contact is likely, safety glasses with side shields are recommended.
Skin protection
Any specific glove information provided is based on published literature and glove manufacturer data. Glove suitability and breakthrough time will differ depending on the specific use conditions. Contact the glove manufacturer for specific advice on glove selection and breakthrough times for your use conditions. Inspect and replace worn or damaged gloves. The types of gloves to be considered for this material include: Nitrile, Viton.
No protection is ordinarily required under normal conditions of use.Any specific clothing information provided is based on published literature or manufacturer data. The types of clothing to be considered for this material include:
No skin protection is ordinarily required under normal conditions of use. In accordance with good industrial hygiene practices, precautions should be taken to avoid skin contact.
Body protection
Always observe good personal hygiene measures, such as washing after handling the material and before eating, drinking, and/or smoking. Routinely wash work clothing and protective equipment to remove contaminants. Discard contaminated clothing and footwear that cannot be cleaned. Practice good housekeeping.Personal protective equipment selections vary based on potential exposure conditions such as applications, handling practices, concentration and ventilation. Information on the selection of protective equipment for use with this material, is based upon intended, normal usage.
Respiratory protection
If engineering controls do not maintain airborne contaminant concentrations at a level which is adequate to protect worker health, an approved respirator may be appropriate. Respirator selection, use, and maintenance must be in accordance with regulatory requirements, if applicable.Types of respirators to be considered for this material include:
Particulate: No special requirements under ordinary conditions of use and with adequate ventilation.
For high airborne concentrations, use an approved supplied?air respirator, operated in positive pressure mode. Supplied air respirators with an escape bottle may be appropriate when oxygen levels are inadequate, gas/vapour warning properties are poor, or if air purifying filter capacity/rating may be exceeded.
9. PHYSICAL AND CHEMICAL PROPERTIES
General information
Appearance
Amber liquid.
Odour
Characteristic.
pH
Not available.
Vapour Pressure
< 0.013 kPa (0.1 mm Hg) at 20°C
Density
(Air = 1): > 2 at 101 kPa
Boiling Point
> 316°C
Melting Point
Not available.
Solubility
Negligible solubility in water.
Specific Gravity of Density
Relative density at 15°C: 0.87
Flash Point
>200°C.
Flammable (Explosive) Limits
LEL: 0.9 UEL: 7.0
Ignition Temperature
Not available.
Formula
Not available.
10. STABILITY AND REACTIVITY
Reactivity
No further relevant information available.
Chemical stability
Stable under normal conditions of use. Material does not decompose at ambient temperatures.
Possibility of hazardous reactions
Will not occur.
Conditions to avoid
Excessive heat. High energy sources of ignition and incompatible materials.
Incompatible materials
Strong oxidisers.
11. TOXICOLOGICAL INFORMATION
Acute effects
No further relevant information available.
Eye contact
Excessive exposure may result in eye irritation.
Irritation (Rabbit): Data available. May cause mild, short?lasting discomfort to eyes. Based on test data for structurally similar materials
Skin contact
Excessive exposure may result in skin irritation; high?pressure injection under skin may cause serious damage.Toxicity (Rabbit): LD50 > 5000 mg/kg
Minimally Toxic. Based on test data for structurally similar materials.
Irritation (Rabbit): Data available. Negligible irritation to skin at ambient temperatures. Based on test data for structurally similar materials.
Ingestion
Low order of toxicity ? effects unknown.Toxicity (Rat): LD50 > 5000 mg/kg
Minimally Toxic. Based on test data for structurally similar materials
Inhalation
Excessive exposure may result in respiratory irritation.
Toxicity (Rat): LC50 > 5000 mg/m³
Minimally Toxic. Based on test data for structurally similar materials.
Irritation: No end point data. Negligible hazard at ambient/normal handling temperatures. Based on assessment of the components.
Toxicity and irritation
No further relevant information available.
12. ECOLOGICAL INFORMATION
Ecotoxicity
Not expected to be harmful to aquatic organisms.
Persistence and degradability
Base oil component ? Expected to be inherently biodegradable
Bioaccumulative potential
Has the potential to bioaccumulate, however metabolism or physical properties may reduce the bioconcentration or limit bioavailability.
Other adverse effects
Base oil component ? Low solubility and floats and is expected to migrate from water to the land. Expected to partition to sediment and wastewater solids.
13. DISPOSAL CONSIDERATIONS
General information
Disposal recommendations based on material as supplied. Disposal must be in accordance with current applicable laws and regulations, and material characteristics at time of disposal. Product is suitable for burning in an enclosed controlled burner for fuel value or disposal by supervised incineration at very high temperatures to prevent formation of undesirable combustion products.

Special Precautions: Empty Container Warning (where applicable): Empty containers may contain residue and can be dangerous. Do not attempt to refill or clean containers without proper instructions. Empty drums should be completely drained and safely stored until appropriately reconditioned or disposed. Empty containers should be taken for recycling, recovery, or disposal through suitably qualified or licensed contractor and in accordance with governmental regulations. DO NOT PRESSURISE, CUT, WELD, BRAZE, SOLDER, DRILL, GRIND, OR EXPOSE SUCH CONTAINERS TO HEAT, FLAME, SPARKS, STATIC ELECTRICITY, OR OTHER SOURCES OF IGNITION. THEY MAY EXPLODE AND CAUSE INJURY OR DEATH.
14. TRANSPORT INFORMATION
ADG label required
HAZCHEM
Not available.

UN Number
None.
Proper shipping name
Not regulated.
Transport hazard class
Void
Packing group
None.
Environmental hazard
Not regulated.
Special precautions for users
Not regulated.
Additional information
Not regulated.
15. REGULATORY INFORMATION
Poisons Schedule Number
Not regulated.
Other Information
No further information available.
16. OTHER INFORMATION
SDS preparation date
9 June 2016
Comments
This information is based on our present knowledge. However, this shall not constitute a guarantee for any specific product features and shall not establish a legally valid contractual relationship.
References
List of Publications referenced when creating this MSDS;
? Hazardous Substances Information System Consolidated Lists: Safe Work Australia.
? APPROVED CRITERIA FOR CLASSIFYING HAZARDOUS SUBSTANCES [NOHSC:1008(2004)] 3rd Edition: National Occupational Health and Safety Commission.
? Dangerous Goods ? Initial Emergency Response Guide (SAA/SNZ HB76:1997).
? IATA Dangerous Goods Regulations.
? Adopted National Exposure Standards for Atmospheric Contaminants in the Occupational Environment [NOHSC:1003(1995)].
? Australia Standard for the Uniform Scheduling of Drugs and Poisons [SUSPD] (Australian Government Department of Health and Ageing).
This Safety Data Sheet (SDS) has been prepared in compliance with the Preparation of Safety Data Sheets for Hazardous Chemicals Code of Practice February 2016. It is the user's responsibility to determine the suitability of this information for adoption of necessary safety precautions. The information published in this SDS has been compiled from the publications listed in Section 16: to the best of our ability and knowledge these publications are considered accurate. We reserve the right to revise Safety Data Sheets as new information becomes available. Copies may be made for non-profit use.

... End of SDS ...