SDS

A listing of SDS's
SAFETY DATA SHEET
Monomer E
1. IDENTIFICATION
Product Identifiers
Product Name:
Lowicryl HM20 - Monomer E (Component of Kit C440)
Other Names:
Lowicryl HM20 Resin; Lowicryl HM20 monostep
Product Number(s):
C440_1
CAS Number:
-
Recommended use of the chemical and restriction on use
Laboratory use.
Company Details
ProSciTech Pty Ltd
11 Carlton Street
KIRWAN QLD 4817
Australia

(07) 4773 9444
www.proscitech.com
Emergency Contact Details
ProSciTech Pty Ltd
11 Carlton Street
KIRWAN QLD 4817
Australia

(07) 4773 9444
www.proscitech.com
2. HAZARDS IDENTIFICATION
Classification of the substance or mixture
GHS02 flame Flam.
Liq. 3 H226 Flammable liquid and vapour.
GHS08 health hazard
Asp. Tox. 1 H304 May be fatal if swallowed and enters airways.
GHS07
Acute Tox. 4 H302 Harmful if swallowed.
Skin Irrit. 2 H315 Causes skin irritation.
Eye Irrit. 2 H319 Causes serious eye irritation.
Skin Sens. 1 H317 May cause an allergic skin reaction.
STOT SE 3 H335 May cause respiratory irritation.
Flam. Liq. 4 H227 Combustible liquid.
Label Elements
Signal Words
Danger
Hazard Statement(s)
Flammable liquid and vapour. Combustible liquid.
Harmful if swallowed. Causes skin irritation.
Causes serious eye irritation.
May cause an allergic skin reaction.
May cause respiratory irritation.
May be fatal if swallowed and enters airways.
Precautionary Statement(s)
Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.
Use explosion-proof electrical/ventilating/lighting/equipment.
Avoid breathing dust/fume/gas/mist/vapours/spray.
Wear protective gloves / eye protection / face protection.
Ground/bond container and receiving equipment.
Use only non-sparking tools.
Take precautionary measures against static discharge.
Wash thoroughly after handling.
Do not eat, drink or smoke when using this product.
Use only outdoors or in a well-ventilated area.
Contaminated work clothing should not be allowed out of the workplace.
Primary route(s) of entry
Not available.
Human Health
Inhalation:
Remove person to fresh air and keep comfortable for breathing.
Call a POISON CENTER/doctor if you feel unwell.
Ingestion:
Immediately call a POISON CENTER/ doctor.
Eyes:
Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Specific treatment (see on this label).
If eye irritation persists: Get medical advice/attention.
Skin:
Wash with plenty of water. Take off contaminated clothing and wash it before reuse.
If skin irritation occurs: Get medical advice/attention.
Environment

In case of fire: Use CO₂, powder or water spray for extinction. Store in a well-ventilated place. Keep container tightly closed. Keep cool. Store locked up. Dispose of contents/container in accordance with local/regional/national/international regulations.
3. COMPOSITION/INFORMATION ON INGREDIENTS
Name
CAS No.
Content (w/w)
Classification
Ethyl methacrylate
97-63-2
50-100%
-
Hexylmethacrylate
142-09-6
10-25%
-
4. FIRST AID MEASURES
Ingestion
Call for a doctor immediately.
Inhalation
In case of unconsciousness place patient stably in side position for transportation.
Skin Contact
Immediately wash with water and soap and rinse thoroughly.
Eye Contact
Rinse opened eye for several minutes under running water. If symptoms persist, consult a doctor.
Other Information
Symptoms of poisoning may even occur after several hours; therefore medical observation for at least 48 hours after the accident.
5. FIREFIGHTING MEASURES
Suitable extinguishing equipment
CO₂, sand, extinguishing powder. Do not use water.
HAZCHEM
Not available.
Special protective equipment and precautions for fire fighters
No special measures required.
For safety reasons unsuitable extinguishing agents: Water with full jet.
6. ACCIDENTAL RELEASE MEASURES
Personal precautions, protective equipment and emergency procedures
Wear protective equipment. Keep unprotected persons away.
Environmental precautions
Do not allow to enter sewers/ surface or ground water.
Methods and materials for containment and clean up
Absorb with liquid-binding material (sand, diatomite, acid binders, universal binders, sawdust).
Dispose contaminated material as waste according to item 13. Ensure adequate ventilation.
Do not flush with water or aqueous cleansing agents.
7. HANDLING AND STORAGE
Precautions for safe handling
Ensure good ventilation/exhaustion at the workplace.
Prevent formation of aerosols.
Conditions for safe storage
Keep container tightly sealed.
Ensure good ventilation/exhaustion at the workplace.
Prevent formation of aerosols.
Keep ignition sources away - Do not smoke.
Protect against electrostatic charge.
Protect from heat and direct sunlight
8. EXPOSURE CONTROLS/PERSONAL PROTECTION
Exposure Standards
Engineering controls
Protect from heat.
Protect against electrostatic charges.
Personal protective equipment
Eye and face protection
Tightly sealed goggles.
Skin protection
Protective gloves
The glove material has to be impermeable and resistant to the product/ the substance/ the preparation.
Due to missing tests no recommendation to the glove material can be given for the product/ the preparation/ the chemical mixture.
Selection of the glove material on consideration of the penetration times, rates of diffusion and the degradation.
Material of gloves
The selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer to manufacturer.
Penetration time of glove material
The exact break through time has to be found out by the manufacturer of the protective gloves and has to be observed.
Body protection
Keep away from foodstuffs, beverages and feed.
Immediately remove all soiled and contaminated clothing.
Wash hands before breaks and at the end of work.
Avoid contact with the eyes and skin.
Respiratory protection
In case of brief exposure or low pollution use respiratory filter device. In case of intensive or longer exposure use self-contained respiratory protective device.
9. PHYSICAL AND CHEMICAL PROPERTIES
General information
Appearance
Colourless liquid
Odour
Ester-like
pH
Not determined.
Vapour Pressure
Not determined.
Density
Not determined.
Boiling Point
249 °C
Melting Point
Undetermined.
Solubility
Not miscible or difficult to mix with water.
Specific Gravity of Density
Not applicable.
Flash Point
76 °C
Flammable (Explosive) Limits
Lower: 1.8 Vol %
Upper: Not determined
Ignition Temperature
Product is not selfigniting.
Formula
Not available.
10. STABILITY AND REACTIVITY
Reactivity
No further relevant information available.
Chemical stability
No decomposition if used according to specifications.
Possibility of hazardous reactions
May occur.
Conditions to avoid
Heat, agine, contamination, oxygen-free atmosphere and incompatible materials.
Incompatible materials
Reducing and oxidising agents.
11. TOXICOLOGICAL INFORMATION
Acute effects
LD/LC50 values relevant for classification:
97-63-2 ethyl methacrylate
Oral LD50 14800 mg/kg (rat)
Eye contact
Irritating effect.
Skin contact
Sensitisation possible through skin contact.
Ingestion
No further relevant information available.
Inhalation
Irritant to skin and mucous membranes,
Toxicity and irritation
The product shows the following dangers according to the calculation method of the General EU Classification Guidelines for Preparations as issued in the latest version: Harmful
Irritant
12. ECOLOGICAL INFORMATION
Ecotoxicity
No further relevant information available.
Persistence and degradability
No further relevant information available.
Bioaccumulative potential
No further relevant information available.
Other adverse effects
Water hazard class 2 (German Regulation) (Self-assessment): hazardous for water
Do not allow product to reach ground water, water course or sewage system.
Danger to drinking water if even small quantities leak into the ground.
13. DISPOSAL CONSIDERATIONS
General information
Must not be disposed together with household garbage. Do not allow product to reach sewage system.
Uncleaned packaging:
Recommendation: Disposal must be made according to official regulations.
14. TRANSPORT INFORMATION
ADG label required
HAZCHEM
Not available.

UN Number
UN1866
Proper shipping name
1866 RESIN SOLUTION
Transport hazard class
3 F
Packing group
III
Environmental hazard
Marine pollutant: Symbol (fish and tree)
Special precautions for users
Warning: Flammable liquids.
Additional information
ADG
Limited quantities (LQ) 5L
Excepted quantities (EQ) Code: E1
Maximum net quantity per inner packaging: 30 ml.
Maximum net quantity per outer packaging: 1000 ml.
Transport category 3 · Tunnel restriction code D/E.
15. REGULATORY INFORMATION
Poisons Schedule Number
S5
Other Information
No further relevant information available.
16. OTHER INFORMATION
SDS preparation date
16 January 2023
Comments
This information is based on our present knowledge. However, this shall not constitute a guarantee for any specific product features and shall not establish a legally valid contractual relationship.
This Safety Data Sheet (SDS) has been prepared in compliance with the Preparation of Safety Data Sheets for Hazardous Chemicals Code of Practice February 2016. It is the user's responsibility to determine the suitability of this information for adoption of necessary safety precautions. The information published in this SDS has been compiled from the publications listed in Section 16: to the best of our ability and knowledge these publications are considered accurate. We reserve the right to revise Safety Data Sheets as new information becomes available. Copies may be made for non-profit use.

... End of SDS ...