SDS

A listing of SDS's
SAFETY DATA SHEET
Conductive Silver Pen, SEM adhesive
1. IDENTIFICATION
Product Identifiers
Product Name:
Conductive Silver Pen, SEM adhesive
Other Names:
Silver Conductive Ink.
Product Number(s):
I008
CAS Number:
-
Recommended use of the chemical and restriction on use
Laboratory use.
Company Details
ProSciTech Pty Ltd
11 Carlton Street
KIRWAN QLD 4817
Australia

(07) 4773 9444
www.proscitech.com
Emergency Contact Details
ProSciTech Pty Ltd
11 Carlton Street
KIRWAN QLD 4817
Australia

(07) 4773 9444
www.proscitech.com
2. HAZARDS IDENTIFICATION
Classification of the substance or mixture
Not classified.
Label Elements
Signal Words
Warning
Hazard Statement(s)
Flammable liquid and vapour.
Harmful if inhaled.
May be harmful if absorbed through skin.
May cause eye and skin irritation.
Contains material that can cause target organ damage.
Precautionary Statement(s)
Do not breathe vapour or mist.
Use only with adequate ventilation.
Do not eat, drink or smoke when using this product.
Avoid contact with eyes, skin and clothing.
Avoid prolonged contact with eyes, skin and clothing.
Keep away from heat, sparks and flame.
Keep container tightly closed.
Wash thoroughly after handling.
Primary route(s) of entry
Not available.
Human Health
Inhalation:
Toxic by inhalation.Adverse symptoms may include the following: headache
Nausea or vomiting
Dizziness/vertigo
Drowsiness/fatigue
Respiratory tract irritation
Unconsciousness
Ingestion:
Harmful if swallowed
Adverse symptoms may include the following: central nervous system depression.
Eyes:
Moderately irritating to eyes.
Adverse symptoms may include the following: irritation
Watering
Redness
Skin:
Harmful in contact with skin:
Adverse symptoms may include the following:
Irritation
Redness
Environment
No further relevant information available.
3. COMPOSITION/INFORMATION ON INGREDIENTS
Name
CAS No.
Content (w/w)
Classification
Silver
7440-22-4
35 - 65
-
n-butyl acetate
123-86-4
5 - 35
-
2-methoxy-1-methylethyl acetate
108-65-6-
2 - 20
-
2-butoxyethyl acetate
112-07-2
2 - 20
-
4. FIRST AID MEASURES
Ingestion
Wash out mouth with water. Do not induce vomiting unless directed to do so by medical personnel. Never give anything by mouth to an unconscious person. Get medical attention immediately.
Inhalation
Move exposed person to fresh air. If not breathing, if breathing is irregular or if respiratory arrest occurs, provide artificial respiration or oxygen by trained personnel. Loosen tight clothing such as a collar, tie, belt or waistband. Get medical attention immediately.
Skin Contact
In case of contact, immediately flush skin with plenty of water for at least 15 minutes while removing contaminated clothing and shoes. Wash clothing before reuse. Clean shoes thoroughly before reuse. Get medical attention immediately.
Eye Contact
Check for and remove any contact lenses. Immediately flush eyes with plenty of water for at least 15 minutes, occasionally lifting the upper and lower eyelids. Get medical attention immediately.
Other Information
No action shall be taken involving any personal risk or without suitable training. If it is suspected that fumes are still present, the rescuer should wear an appropriate mask or self-contained breathing apparatus. It may be dangerous to the person providing aid to give mouth-to-mouth resuscitation. Wash contaminated clothing thoroughly with water before removing it, or wear gloves
No specific treatment. Treat symptomatically. Contact poison treatment specialist immediately if large quantities have been ingested or inhaled.
Repeated exposure may cause skin dryness or cracking.
5. FIREFIGHTING MEASURES
Suitable extinguishing equipment
Use dry chemical, CO₂, water spray (fog) or foam.
HAZCHEM
Not available.
Special protective equipment and precautions for fire fighters
Promptly isolate the scene by removing all persons from the vicinity of the incident if there is a fire. No action shall be taken involving any personal risk or without suitable training. Move containers from fire area if this can be done without risk. Use water spray to keep fire-exposed containers cool.
Fire-fighters should wear appropriate protective equipment and self-contained breathing apparatus (SCBA) with a full face-piece operated in positive pressure mode.
6. ACCIDENTAL RELEASE MEASURES
Personal precautions, protective equipment and emergency procedures
No action shall be taken involving any personal risk or without suitable training. Evacuate surrounding areas. Keep unnecessary and unprotected personnel from entering. Do not touch or walk through spilled material. Shut off all ignition sources. No flares, smoking or flames in hazard area. Do not breathe vapour or mist. Provide adequate ventilation. Wear appropriate respirator when ventilation is inadequate. Put on appropriate personal protective equipment (see Section 8).
Environmental precautions
Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers. Inform the relevant authorities if the product has caused environmental pollution (sewers, waterways, soil or air).
Methods and materials for containment and clean up
Stop leak if without risk. Move containers from spill area. Use spark-proof tools and explosion-proof equipment. Dilute with water and mop up if water-soluble. Alternatively, or if water-insoluble, absorb with an inert dry material and place in an appropriate waste disposal container. Dispose of via a licensed waste disposal contractor.
Stop leak if without risk. Move containers from spill area. Use spark-proof tools and explosion-proof equipment. Approach release from upwind. Prevent entry into sewers, water courses, basements or confined areas. Wash spillages into an effluent treatment plant or proceed as follows. Contain and collect spillage with non-combustible, absorbent material e.g. sand, earth, vermiculite or diatomaceous earth and place in container for disposal according to local regulations (see Section 13). Dispose of via a licensed waste disposal contractor. Contaminated absorbent material may pose the same hazard as the spilled product. Note: see Section 1 for emergency contact information and Section 13 for waste disposal.
7. HANDLING AND STORAGE
Precautions for safe handling
Put on appropriate personal protective equipment (see Section 8). Eating, drinking and smoking should be prohibited in areas where this material is handled, stored and processed. Workers should wash hands and face before eating, drinking and smoking. Remove contaminated clothing and protective equipment before entering eating areas. Do not get in eyes or on skin or clothing. Do not breathe vapour or mist. Do not ingest.
Use only with adequate ventilation. Wear appropriate respirator when ventilation is inadequate. Do not enter storage areas and confined spaces unless adequately ventilated. Keep in the original container or an approved alternative made from a compatible material, kept tightly closed when not in use. Store and use away from heat, sparks, open flame or any other ignition source. Use explosion-proof electrical (ventilating, lighting and material handling) equipment. Use non-sparking tools. Take precautionary measures against electrostatic discharges. To avoid fire or explosion, dissipate static electricity during transfer by grounding and bonding containers and equipment before transferring material. Empty containers retain product residue and can be hazardous. Do not reuse container.
Conditions for safe storage
Store in accordance with local regulations. Store in a segregated and approved area. Store in original container protected from direct sunlight in a dry, cool and well-ventilated area, away from incompatible materials (see Section 10) and food and drink. Eliminate all ignition sources. Separate from oxidising materials. Keep container tightly closed and sealed until ready for use. Containers that have been opened must be carefully resealed and kept upright to prevent leakage. Do not store in unlabelled containers.
Use appropriate containment to avoid environmental contamination.
8. EXPOSURE CONTROLS/PERSONAL PROTECTION
Exposure Standards
Material
TWA ppm
TWA mg/m3
STEL ppm
STEL mg/m3
silver
-
0.01 mg/m³, (as Ag) 10 hours.
-
-
n-butyl acetate
150 ppm 10 hours
710 mg/m³ 10 hours-
200 ppm 15 minutes.
950 mg/m³ 15 minutes-
2-methoxy-1-methylethyl acetate-
50 ppm 8 hours
-
-
-
2-butoxyethyl acetate
33 mg/m³ 10 hours.-
-
-
-
Engineering controls
Use only with adequate ventilation. Use process enclosures, local exhaust ventilation or other engineering controls to keep worker exposure to airborne contaminants below any recommended or statutory limits. The engineering controls also need to keep gas, vapour or dust concentrations below any lower explosive limits. Use explosion-proof ventilation equipment.
Personal protective equipment
Eye and face protection
Safety eyewear complying with an approved standard should be used when a risk assessment indicates this is necessary to avoid exposure to liquid splashes, mists or dusts. If contact is possible, the following protection should be worn, unless the assessment indicates a higher degree of protection: chemical splash goggles.
Skin protection
Personal protective equipment for the body should be selected based on the task being performed and the risks involved and should be approved by a specialist before handling this product.
When there is a risk of ignition from static electricity, wear anti-static protective clothing. For the greatest protection from static discharges, clothing should include anti-static overalls, boots and gloves.
Body protection
Chemical-resistant, impervious gloves complying with an approved standard should be worn at all times when handling chemical products if a risk assessment indicates this is necessary. Considering the parameters specified by the glove manufacturer, check during use that the gloves are still retaining their protective properties. It should be noted that the time to breakthrough for any glove material may be different for different glove manufacturers. In the case of mixtures, consisting of several substances, the protection time of the gloves cannot be accurately estimated.
Respiratory protection
Use a properly fitted, air-purifying or air-fed respirator complying with an approved standard if a risk assessment indicates this is necessary. Respirator selection must be based on known or anticipated exposure levels, the hazards of the product and the safe working limits of the selected respirator.
9. PHYSICAL AND CHEMICAL PROPERTIES
General information
Appearance
Gray liquid
Odour
Not available.
pH
Not available.
Vapour Pressure
0.67 kPa (5 mm Hg) [room temperature]
Density
2
Boiling Point
126°C (258.8°F)
Melting Point
Not available.
Solubility
Not dispersible in the following materials: cold water, hot water, methanol, diethyl ether, n-octanol and acetone.
Specific Gravity of Density
Not available.
Flash Point
Closed cup: 24°C (75.2°F) [Tagliabue
Flammable (Explosive) Limits
Not available.
Ignition Temperature
Not available.
Formula
Not available.
10. STABILITY AND REACTIVITY
Reactivity
No further relevant information available.
Chemical stability
The product is stable.
Possibility of hazardous reactions
Under normal conditions of storage and use, hazardous reactions will not occur.
Conditions to avoid
Avoid all possible sources of ignition (spark or flame). Do not pressurise, cut, weld, braze, solder, drill, grind or expose containers to heat or sources of ignition.
Incompatible materials
Reactive or incompatible with the following materials: oxidising materials acids alkalis.
11. TOXICOLOGICAL INFORMATION
Acute effects
No further relevant information available.
Eye contact
No further relevant information available.
Skin contact
No further relevant information available.
Ingestion
No further relevant information available.
Inhalation
No further relevant information available.
Toxicity and irritation
No further relevant information available.
12. ECOLOGICAL INFORMATION
Ecotoxicity
No known significant effects or critical hazards.
Persistence and degradability
No further relevant information available.
Bioaccumulative potential
No further relevant information available.
Other adverse effects
No known significant effects or critical hazards.
13. DISPOSAL CONSIDERATIONS
General information
The generation of waste should be avoided or minimized wherever possible. Disposal of this product, solutions and any by-products should at all times comply with the requirements of environmental protection and waste disposal legislation and any regional local authority requirements. Dispose of surplus and non-recyclable products via a licensed waste disposal contractor. Waste should not be disposed of untreated to the sewer unless fully compliant with the requirements of all authorities with jurisdiction. Waste packaging should be recycled. Incineration or landfill should only be considered when recycling is not feasible. This material and its container must be disposed of in a safe way. Care should be taken when handling emptied containers that have not been cleaned or rinsed out. Empty containers or liners may retain some product residues. Vapor from product residues may create a highly flammable or explosive atmosphere inside the container. Do not cut, weld or grind used containers unless they have been cleaned thoroughly internally. Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers
14. TRANSPORT INFORMATION
ADG label required
HAZCHEM
Not available.

UN Number
Proper shipping name
Paint
Transport hazard class
3
Packing group
PG III
Environmental hazard
No information available.
Special precautions for users
Limited quantity.
Additional information
No information available.
15. REGULATORY INFORMATION
Poisons Schedule Number
Not listed.
Other Information
Flammable liquid
Toxic material
Irr
16. OTHER INFORMATION
SDS preparation date
16 August 2017
Comments
This information is based on our present knowledge. However, this shall not constitute a guarantee for any specific product features and shall not establish a legally valid contractual relationship.
This Safety Data Sheet (SDS) has been prepared in compliance with the Preparation of Safety Data Sheets for Hazardous Chemicals Code of Practice February 2016. It is the user's responsibility to determine the suitability of this information for adoption of necessary safety precautions. The information published in this SDS has been compiled from the publications listed in Section 16: to the best of our ability and knowledge these publications are considered accurate. We reserve the right to revise Safety Data Sheets as new information becomes available. Copies may be made for non-profit use.

... End of SDS ...